| | High Level Instrument Disinfectant
Active Ingredients:
15% Isopropylol; 0.5% QAC Blend;
0.5% Tertiary Amine; 0.8% pH Buffer;
0.8% Corrosion Inhibitor; 0.3% Surfactant
Product characteristics:
Ready-to-use; Unfragranced;
Non-corrosive; Non-toxic; Non-staining
Non-caustic; Biodegradeable
Recommended Uses:
Disinfection of pre-cleaned
thermo-sensitive instruments.
Disinfection of pre-cleaned
instruments where a functional calibrated
autoclave is unavailable.
Where access to an approved, regularly maintained and tested autoclave is available, the autoclave should always be considered the primary means of sterilisation.
Instructions for use:
Decant the required amount of Cold Sterilant into a clean, dry, covered stainless steel or HDPE receptacle. Completely immerse thoroughly disassembled, pre-cleaned, rinsed & dried instruments / devices in the liquid, ensuring that any hinges or joints are in the open position. Allow a contact time as per your desired efficacy – see below efficacy table. Remove the instruments / devices from the liquid using sterile forceps, and follow the post-sterilisation procedure of the facility. Tray-life of the liquid should be tested weekly using M.E.C. strips. The product should have a tray-life of between 21 & 28 days, should the strips prove a shorter life, check your instrument cleaning process. For best results, replace the liquid every 28 days, or as soon as an MEC Test Strip reads less than 1000ppm active ingredient, or immediately if any change in liquid colour occurs.
Pre-Requirements:
Latex or nitrile gloves for sensitive skin, however OHSA requires the use of eye protection & good ventilation when mixing, handling or discarding chemical disinfectants.
Product Description:
- Available sizes: 20L, 5L, 1L
- Dilution Factor: Ready to use
- Physical Form: Translucent blue liquid
- Odour: Mild chemical fragrance
- pH: 7-8
- Tray Life: 21-28 days (MEC Test Strips available)
- Product Risk Classification: C / IIb
- GMDN Code: 47631
- GMDN Descriptor: Medical Device Disinfectant
- NRCS Reg. no: CT29GNR529/242056/040/497
- Incompatibilities: Anionic detergents, Natural Soaps, Strong oxidisers
| | |
STESC2 | | | |
| | |
| | Thryve Mouth Salts
Controls and helps treat
- Bad breath
- Sore throats
- Mouth ulcers
- Bleeding and swollen gums
Simply… brush 2x daily and gargle
Mouth Health = Body Health
- Natural antibacterial
- Cleanses and removes plaque
- Promotes fresh breath
- Rebuilds gum health
- Treats inflammation and gingivitis
- Helps bring brightness back to your teeth – gently
Ingredients & Benefits
Sea salt
- Anti-bacterial
- Anti-microbial
- Anti-fungal
- Anti-viral
- Natural preservative
- Saliva production stimulant
- Ph regulator
Bentonite Clay
- Natural source of important minerals
- Alkalises the body
- Binds to unhealthy substances in the mouth and helps to remove them
Xylitol
- Reduced levels of bad bacteria in the mouth by up to 75%
- Helps to control halitosis
- Increases absorption of calcium
- Reduces plaque formation
Liquorice Extract
- Creates a hostile environment for cavity causing bacteria
- Anti-viral
- Anti-oxidant
- Aids digestion
- Cortisol level regulator
White Willow Extract
- Helps for pain relief
- Anti-inflammatory
Green Tea Extract
- Prevents formation of dental plaque
- Anti-bacterial
- Anti-oxidant
- Improves brain function
- Weight reduction
- Lowers risk of type 2 Diabetes
- Improves liver function
Clove Bud Oil
- The strongest anti-oxidant value of all studied plants. No 1 on the ORAC scale
- Anti-fungal
- Anti-microbial
- Digestive aid
- Expectorant
- Anti-inflammatory
- Analgesic
- Topical anesthetic in oral care
Peppermint Oil
- Anti-bacterial
- Anti-inflammatory
- Soothes pain
- Increases blood circulation in gum tissue
- Eliminates bad breath
Thryve mouth salts helps neutralise acids in the throat and maintain a healthy pH balance, preventing unwanted bacteria from accumulating and causing infections.
| | |
THR100 | | | |
| | |
| | Thryve mouth spray 200PPM 125ML
Indications
Helps to support the treatment of oral infections such as gingivitis, periodontitis, and oral thrush.
Directions
- Ready to use. Spray 5 x per application Spray as needed, or minimum 3 x per day
Ingredients
- Electrolysed saline solution (HOCI ±200ppm)
- pH 5-7
- This product contains no alcohol.
Precautions
Storage
- Store below 25°C.
- Keep out of direct sunlight
- Recommended to use within 30 days after opening.
| | |
THR222 | | | |
| | |
| | High Level Instrument Disinfectant
Active Ingredients:
15% Isopropylol; 0.5% QAC Blend;
0.5% Tertiary Amine; 0.8% pH Buffer;
0.8% Corrosion Inhibitor; 0.3% Surfactant
Product characteristics:
Ready-to-use; Unfragranced;
Non-corrosive; Non-toxic; Non-staining
Non-caustic; Biodegradeable
Recommended Uses:
Disinfection of pre-cleaned thermo-sensitive instruments. Disinfection of pre-cleaned
instruments where a functional calibrated autoclave is unavailable.
Instructions for use:
Decant the required amount of Cold Sterilant into a clean, dry, covered stainless steel or HDPE receptacle. Completely immerse thoroughly disassembled, pre-cleaned, rinsed & dried instruments / devices in the liquid, ensuring that any hinges or joints are in the open position. Allow a contact time as per your desired efficacy – see below efficacy table. Remove the instruments / devices from the liquid using sterile forceps, and follow the post-sterilisation procedure of the facility. Tray-life of the liquid should be tested weekly using M.E.C. strips. The product should have a tray-life of between 21 & 28 days, should the strips prove a shorter life, check your instrument cleaning process. For best results, replace the liquid every 28 days, or as soon as an MEC Test Strip reads less than 1000ppm active ingredient, or immediately if any change in liquid colour occurs.
Pre-Requirements:
Latex or nitrile gloves for sensitive skin, however OHSA requires the use of eye protection & good ventilation when mixing, handling or discarding chemical disinfectants.
Product Description:
Available sizes: 20L, 5L, 1L
Dilution Factor: Ready to use
Physical Form: Translucent blue liquid
Odour: Mild chemical fragrance
pH: 7-8
Tray Life: 21-28 days (MEC Test Strips available)
Product Risk Classification: C / IIb
GMDN Code: 47631
GMDN Descriptor: Medical Device Disinfectant
NRCS Reg. no.: ACT29GNR529/242056/040/497
Medical Device Reg. No.: Awaiting Class Registration Call-up
Incompatibilities: Anionic detergents, Natural Soaps, Strong oxidisers
| | |
STEST2 | | | |
| | |
| | In-Situ Vacuum System Line Detergent-Disinfectant
Active Ingredients:
4.25% 5th Generation Quaternary Ammonium Compound blend
Product characteristics:
Super-concentrated; Unfragranced; Non-corrosive; Non-toxic; Non-staining Non-caustic; Biodegradeable
Recommended Uses:
In-situ terminal cleaning, disinfection & odour control of healthcare suction systems.Odour control & unblocking of inground drains which contain congealed organic matter. Cleaning & disinfection of hard to reach, non-sensitive areas in air conditioning systems.
Instructions for use:
Shake well before use. Dilute Disinfecting Suction Cleaner as per below efficacy table, where 1% equals 10mL product per 1L of water or 1 dosing pump with 2.5L of water.. Pour or aspirate the diluted solution into the system. Allow the contact time of your required efficacy before flushing the system. For badly maintained systems (or the initial 4 uses), leave the solution in the system overnight, flushing the system the following morning. Dilute only enough for immediate single use – if unused, discard within 7 days of dilution. Repeat daily.
Pre-Requirements:
Latex gloves & chemical splash goggles are required when handling or discarding the product.
Product Description:
Available sizes: 20L, 5L, 1L, 1L Dosing Bottle
Dilution Factor: 1:100 or 1% (10mL per L)
Physical Form: Translucent pink-orange liquid
Odour: Mild chemical smell
pH: Concentrate and dilute: 12-13
Risk Classification: B / IIa
GMDN Code: 47631
GMDN Descriptor: Medical Device Disinfectant
NRCS Reg. no.: ACT29GNR529/242056/040/496
Medical Device Reg. No.: Awaiting Class Registration Call-up
Incompatibility: Anionic detergents, Strong oxidisers
| | |
STESV2D | | | |
| | |
| | HealthCare Surface & Equipment Disinfecting Wipes
Active Ingredients:
0.075% Fifth generation QAC Blend;
0.5% Preservative.
Product characteristics:
Vacuum-impregnated; Unfragranced;
Non-corrosive; Non-toxic; Non-staining
Non-caustic; Convenient
Recommended Uses:
Healthcare surface disinfection.
Medical Device disinfection.
Disinfection of high-touch items, especially where the use of a spray disinfectant is inadvisable.
Instructions for use:
To begin: Remove the lid & remove the sealed inner bag. Ensure that the leading wipe is at the top, cut open the bag & place it back in the tub. Open the flap in the lid & pull the leading wipe slowly through the hole. Replace the lid onto the tub and the wipes are ready to use. When needed: Simply pull out a wipe, tear it off on the perforation and use. Best results are achieved when used on a visibly clean, dry surface. Allow the contact time of your required efficacy, (as per the efficacy table below right), before using the surface again. Repeat as often as required by your Infection Control protocol (suggested protocols available on request). Always ensure that the flap is tightly shut after use to prevent drying out of the wipes. Wipe material is not efficiently biodegradable.
Pre-Requirements:
None strictly necessary, however OHSA requires the use of eye protection & good ventilation when mixing, handling or discarding chemical disinfectants.
Product Description:
Available sizes: 100s Tub; 100s Refill (Wipe Size: 200mm x 140mm)
Dilution Factor: Not applicable - pre-impregnated wipe
Physical Form: White, non-woven wipe
Odour: Mild chemical fragrance
pH: 5-6.5
Risk Classification: B / II
GMDN Code: 58077
GMDN Descriptor:
Medical Device Disinfection Wipe
NRCS Reg. no.: ACT5GNR529/242613/040/0256
Medical Device Reg. No.: Pending
Incompatibility: Anionic detergents, Natural Soaps, Strong oxidisers
| | |
STESW2 | | | |
| | |
| |
HealthCare Surface & Equipment Disinfecting Wipes
Active Ingredients:
0.075% Fifth generation QAC Blend;
0.5% Preservative.
Product characteristics:
Vacuum-impregnated; Unfragranced;
Non-corrosive; Non-toxic; Non-staining
Non-caustic; Convenient
Recommended Uses:
Healthcare surface disinfection.
Medical Device disinfection.
Disinfection of high-touch items, especially where the use of a spray disinfectant is inadvisable.
Instructions for use:
To begin: Remove the lid & remove the sealed inner bag. Ensure that the leading wipe is at the top, cut open the bag & place it back in the tub. Open the flap in the lid & pull the leading wipe slowly through the hole. Replace the lid onto the tub and the wipes are ready to use. When needed: Simply pull out a wipe, tear it off on the perforation and use. Best results are achieved when used on a visibly clean, dry surface. Allow the contact time of your required efficacy, (as per the efficacy table below right), before using the surface again. Repeat as often as required by your Infection Control protocol (suggested protocols available on request). Always ensure that the flap is tightly shut after use to prevent drying out of the wipes. Wipe material is not efficiently biodegradable.
Pre-Requirements:
None strictly necessary, however OHSA requires the use of eye protection & good ventilation when mixing, handling or discarding chemical disinfectants.
Product Description:
Available sizes: 100s Tub; 100s Refill (Wipe Size: 200mm x 140mm)
Dilution Factor: Not applicable - pre-impregnated wipe
Physical Form: White, non-woven wipe
Odour: Mild chemical fragrance
pH: 5-6.5
Risk Classification: B / II
GMDN Code: 58077
GMDN Descriptor:
Medical Device Disinfection Wipe
NRCS Reg. no.: ACT5GNR529/242613/040/0256
Medical Device Reg. No.: Pending
Incompatibility: Anionic detergents, Natural Soaps, Strong oxidisers
| | |
STESW4 | | | |
| | |
| | PrimeSafe Alcohol Surface Spray
Active Ingredients:
PrimeSafe Alcohol Surface Spray contains 70% v/v Isopropylol; 30% Inert Ingredients
Product characteristics:
User friendly, stable, Efficacy first, Safe, Convenient, Versatile
Recommended Uses:
Clinical Surface disinfection. Laboratory surface and equipment disinfection. Disinfection of items where a water-based product cannot be used.
Instructions for use:
Thoroughly pre-clean and rinse the surface wherever possible. Spray PrimeSafe Alcohol Surface Spray uniformly over the surface from a distance of about 30cm away, ensuring that the surface is completely covered. Allow the surface to dry naturally, or for a minimum contact time of 1 minute, prior to using the surface again.
Pre-Requirements:
Latex gloves for sensitive skin, however OHSA requires the use of eye protection & good ventilation when mixing, handling or discarding chemical disinfectants.
Product Description:
Available sizes: 20L, 5L, 1L Trigger Spray
Dilution Factor: Ready to use
Physical Form: Translucent liquid
Odour: Mild alcohol odour
pH: 6.5-7.5
Risk Classification: B / IIa
GMDN Code: 47631
GMDN Descriptor: Medical Device Disinfectant
NRCS Reg. no.: ACT5GNR529/242613/090/0781
Medical Device Reg. No.: Awaiting Registration Call-up
Incompatibility: Do not mix with other chemicals
| | |
PRIPASS2 | | | |
| | |
| | High-Level Instrument Disinfectant
Active Ingredients:
0.575% Ortho-pthalaldehyde;
0.4% Rust Inhibitor; 2% Surfactant; 97.025% Inert Ingredients
Product characteristics:
Ready-to -use; Locally Made;
Non-corrosive; Non-staining Non-caustic; Biodegradeable
Recommended Uses:
Sterilisation / disinfection of pre-cleaned thermo-sensitive instruments. Sterilisation / disinfection of pre-cleaned instruments where a functional calibrated autoclave is unavailable.
Instructions for use:
Decant the required amount of OPA into a clean, dry, covered stainless steel or HDPE receptacle. Completely immerse thoroughly disassembled, pre-cleaned, rinsed & dried instruments / devices in the liquid, ensuring that any hinges or joints are in the open position. Allow a contact time as per your desired efficacy – see below efficacy table. Remove the instruments / devices from the liquid using sterile forceps, and follow the post-sterilisation procedure of the facility. Tray-life of the liquid should be tested weekly using M.E.C. strips. The product should have a tray-life of between 14 & 21 days, should the strips prove a shorter life, check your instrument cleaning process. For best results, replace the liquid every 14 days, or as soon as an MEC Test Strip reads less than 0.5% active ingredient, or immediately if any change in liquid colour occurs.
Pre-Requirements:
Latex or nitrile gloves, protective aprons and chemical splash goggles. Use only in well-ventilated areas.
Product Description:
Available sizes: 20L, 5L, 1L
Dilution Factor: Ready to use
Physical Form: Pale yellow liquid
Odour: Chemical Odour
pH: 7-9
Risk Classification: C / IIb
GMDN Code: 40579
GMDN Descriptor: Gluteraldehyde Device Sterilant
NRCS Reg. no.: Pending
Medical Device Reg. No.: Awaiting Registration Call-up
Incompatibility: Do not mix with other chemicals
| | |
PRIPOP2 | | | |
| | |
| | | | |
627401 | | | |
| | |
| | | | |
627400 | | | |
| | |
| | | | |
627399 | | | |
| | |
| | Ivoclar Vivadent Clinical Accessories and Instruments
Optragate Assortment
Moisture control made easy. OptraGate retracts the lips and cheeks evenly and gently, allowing more effective, relative isolation of the treatment field. The soft, flexible material adapts to the movements of the mouth in a controlled manner and is comfortable to wear for patients e.g. during the occlusion check or X-ray imaging of the teeth.
The dentist and the dental assistant can better control a clean treatment field because OptraGate allows easy access. Dental mirrors and vacuum are used for retaining the tongue and can thus, be used in a precise and effective manner. In combination with other auxiliary equipment, such as parotid pads or sublingual cotton rolls relative isolation of the treatment field is optimized which results in more efficient and simplified treatment procedures.
The main product benefits include:-
- Easy access to the cavity
- Lips and cheeks are evenly retracted around the mouth
- Easily accessible, manageable treatment field
- Effective and quick relative isolation
Relaxed and more efficient treatment procedure:-
- Easy placement
- Increased concentration on the actual treatment procedure
- Relieves the work of the dental assistant and dentist.
High patient comfort of wear:-
- 3-dimensional flexibility for a very good positioning
- Soft, flexible material with recesses to accommodate the upper and lower lip frenulum
- Good compatibility thanks to the latex-free material
Contains 40 x OptraGate each Regular and Small, and instructions.
| | |
577275 | | | |
| | |
| | | | |
683378 | | | |
| | |
| | | | |
683376 | | | |
| | |
| | | | |
683377 | | | |
| | |
| | Ivoclar Vivadent Clinical Accessories and Instruments
OptraGate Small Assortment Blue & Pink
OptraGate is an innovative auxiliary aid that enables the treatment field to be enlarged easily and comfortably. The material quality of the new successor version OptraGate “ExtraSoft” has been optimized to provide enhanced patient comfort and snug fit, especially in the area of the upper and lower frenum. In addition to adult sizes “Regular” and “Small”, OptraGate is also available for children in size “Junior”.
Advantages:
- Full view of the working field and good access
- High level of patient comfort due to three-dimensional elasticity
- Wide range of applications
- Latex Free
Includes:
- Small pink x 20
- Small blue x 20
| | |
669088 | | | |
| | |
| | Ivoclar Vivadent Clinical Accessories and Instruments
OptraGate Junior Assortment Blue & Pink
OptraGate is an innovative auxiliary aid that enables the treatment field to be enlarged easily and comfortably. The material quality of the new successor version OptraGate “ExtraSoft” has been optimized to provide enhanced patient comfort and snug fit, especially in the area of the upper and lower frenum. In addition to adult sizes “Regular” and “Small”, OptraGate is also available for children in size “Junior”.
Advantages:
- Full view of the working field and good access
- High level of patient comfort due to three-dimensional elasticity
- Wide range of applications
- Latex Free
Includes:
- Junior pink x 20
- Junior blue x 20
| | |
669089 | | | |
| | |
| | | | |
GAMMAFIX_TRAY_CINC | |
| |
| | |
| | | | |
RUBBER_DAM_CLAMP |
| |
|
| | |
| | | | |
RUBBER_DAM_CLAMP_LOWER_M |
| |
|
| | |
| | | | |
RUBBER_DAM_CLAMP_MOLARS |
| |
|
| | |
| | | | |
RUBBER_DAM_CLAMP_PREMOLA |
| |
|
| | |
| | | | |
RUBBER_DAM_CLAMP_UPPER_M |
| |
|
| | |